EarthQuake WE43 Spezifikationen PDF herunterladen (Seite 14)

Page 14

OPERATOR INSTRUCTIONS AND PARTS

WE43E & WE43 Edger

GetEarthquake.com

800-345-6007

Steps for Cleaning Air Filter

1. Wash in warm water with liquid detergent and water until

dirt and debris are removed. Press ﬁlter when washing,

do not twist.

2. Rinse in warm water until soap and dirt are removed.

3. Dry ﬁlter by wrapping in a clean cloth and pressing ﬁlter

until it is dry.

4. Apply a lightweight motor oil or thin based machine oil

to the entire ﬁlter.

5. Remove excess oil.

6. Attach the ﬁlter and air cleaner cover to the engine.

Spark Plug

The recommended spark plug is a NGK BM6A which cross

references to a Champion CJ8.

1. Check spark plug at the beginning of each season.

2. Disconnect the spark plug cap, and clean any debris

from around the spark plug area.

3. Remove spark plug and replace if any of the following

occur; pitted electrodes, burned electrodes, cracked

porcelain, or deposits around electrodes.

4. After analysis, seat spark plug and tighten with spark

plug wrench. Reconnect the spark plug wire.

• Reinstall original spark plug, tighten additional 1/2

turn.

• Installing new spark plug, adjust spark plug gap to .028”

and tighten additional 1/8 – 1/4 turn .

NOTE: Loose spark plug may overheat and damage

engine. Over tightened spark plug may damage threads

in the cylinder head.

Carburetor

Never tamper with factory setting of the carburetor.

TRANSPORTING YOUR EDGER

1. Never transport engine inside an enclosed space or

vehicle. Fuel or fuel vapors may ignite causing serious

injury or death.

2. If fuel is present in the fuel tank, transport in an open

vehicle in an upright position.

3. If an enclosed vehicle must be used, remove gas into an

approved red fuel container. DO NOT siphon by mouth.

4. Run engine to use up the fuel in the carburetor and fuel

tank. Always run engine in a well ventilated area.

5. Wipe away any spilled fuel from engine and edger. Allow

to dry.

LONG TERM STORAGE

If your edger will not be used for more than one month,

prepare it for long term storage.

Steps for Long Term Storage

1. Remove the remainder of the fuel from the gas tank into

an approved fuel container.

2. Store edger (engine) in a vertical position.

3. Remove all debris from edger (engine).

SERVICE INFORMATION

At Ardisam, we build quality and durability into the design of our

products; but no amount of careful design by us, and careful

maintenance by you, can guarantee a repair-free life for your

machine. Most repairs will be minor, and easily ﬁxed by following

the suggestions in the troubleshooting guide in this section.

The guide will help you pinpoint the causes of common

problems and identify remedies.

For more complicated repairs, you may want to rely on your

retailer, an authorized mechanic or Ardisam, Inc. (contact

your retailer for a list of authorized mechanics in your area).

A parts catalog is included in this section.

We will always be glad to answer any questions you have,

or help you ﬁnd suitable assistance. To order parts or inquire

about warranty, call or write us at the address found below,

under the section ordering repair parts.

ORDERING REPAIR PARTS

Parts can be obtained from the store where your edger

was purchased, direct from the factory or online. To order

from the factory, call or write to:

Ardisam, Inc.

1690 Elm Street, Cumberland, Wisconsin 54829

1-800-345-6007 • 1-715-822-2415

E-mail: info@ardisam.com

Please include the following information with your order:

1. Part numbers

2. Part description

3. Quantity

4. Model number and serial number

NOTE: When ordering from manufacturer, there is a

$10.00 minimum order.

IMPORTANT

NEVER TWIST AIR FILTERS WHEN CLEANING.

ALWAYS PRESS.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

EarthQuake WE43 Spezifikationen Seite 14

Kommentare zu diesen Handbüchern